B – 02 Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes, aluminum alloy, aluminum-alloy drawn seamless tubes. ASTM B/ASME SB SPECIFIATION FOR ANLUMINUM AND ALUMINUM- ALLOY DRAWN SEAMLESS TUBES. This specification covers. ASTM Bpdf – Free download as PDF File .pdf), Text File .txt) or view presentation slides online.
|Published (Last):||26 October 2009|
|PDF File Size:||9.22 Mb|
|ePub File Size:||6.42 Mb|
|Price:||Free* [*Free Regsitration Required]|
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are astm b210 provided as part of the standard. ASTM does not give astm b210 warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
Alloy Alclad F.
ASTM B – 00 Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes
The producer may analyze samples astm b210 trace elements not specified in the specification. Alloy F O 0.
Link to Active This link will always route to the current Active version of the standard. Coiled tubes are generally available only as round tubes with a wall thickness not exceeding 0. Alloy Alclad F O 0. Astm b210 Version s astm b210 view previous versions of standard.
ASTM B210 Aluminum-Alloy Drawn Seamless Tubes Manufacturer
The tension tests shall be made in astm b210 with test methods Astm b210 M. Tensile Strength, ksi Yield Strength D 0. The different methods for leak testing of tubes aztm presented. The determination of chemical composition shall be made in accordance with suitable chemical test methods E 34or spectrochemical test methods E and Emethods.
astm b210 J Composition of cladding alloy as applied during the course of manufacture. Astm b210 is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. This specification covers aluminum and aluminum-alloy drawn seamless tubes in straight lengths and coils for general purpose.
6061 Drawn Aluminum Tubing
However, such analysis is not required and may not cover all metallic Others elements. The tube shall be produced by drawing an extruded tube made from hollow extrusion ingot cast in hollow form or pierced and extruded by the use astm b210 the die and mandrel method. This abstract is a brief summary astm b210 the referenced standard.
Work Item s – proposed revisions of this standard. Flattening test specimens shall be aatm sidewise under a gradually astm b210 load so as to give a uniform radius of bend until astm b210 minimum outside diameter under load is asrm more than F times the wall thickness of the tube astm b210 specified.
When specified, heat treatment of applicable tempers shall be in accordance with practice B Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Totalthe material shall be considered non-conforming.
Aluminum Tubing – AMS-WWT/6, ASTM B, AMS-T, , , | TW Metals
The samples from astm b210 tube shall not be required to conform to these limits. The tubes shall conform to the chemical composition requirements specified.
A Limits are in weight percent maximum unless shown as a range or otherwise stated. I Alloy clad with Alloy It astm b210 the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
E Others includes astm b210 elements for which no specific limit is shown as well as unlisted metallic elements.
The ashm shall conform to the tensile property requirements specified. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A for aluminum designation in accordance with Practice E Note 2—Throughout this specification, use of the term alloy in the general sense includes aluminum as b201 as aluminum alloy. F Other elements Total shall be the sum of unspecified metallic elements 0. H The aluminum astm b210 shall be calculated by subtracting from C For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit astm b210 the last right-hand place of figures used in expressing the specified limit, in accordance with the rounding-off method of Practice E T4, T42 Astm b210 0.
Aluminum F Astm b210 0. B Analysis shall be made for the elements for which limits are shown in this table.